joint flange
英 [dʒɔɪnt flændʒ]
美 [dʒɔɪnt flændʒ]
网络 联结法兰; 接头法兰; 接合凸缘
双语例句
- Joint for tubing of asbestos ( excl. of asbestos cement) flange bobbin for warping ( cotton)
石棉管道接头（不包括石棉水泥制的）经法兰绕线筒（棉） - Align mark on front universal joint, or CV joint, to the mark on the axle pinion yoke, or flange.
将前万向节或CV万向节上的标志与车轴小齿轮轴轭或凸缘上的标志对准。 - Pull plastic sleeve straight off the joint flange.
径直将塑料套管从连接法兰中拔下。 - Fit joint flange for vibration balancer.
安装振动平衡器的连接法兰。 - Remove joint flange behind the vibration balancer.
拆下振动平衡器后面的连接法兰。 - Manufacturer shall confirm compatibility of material of joint ring with the flange material and process conditions.
制造商应确定接合环材料与法兰材料以及工艺条件的兼容性。 - The utility model discloses a socket of a reaction cauldron, which is composed of a germinal lid joint flange, a socket body and a cauldron port joint flange.
反应釜套节，由孔盖接头法兰、套节主体和釜口接头法兰构成。 - The results show that the initial stiffness and the ultimate carrying capacity of splice joint with cantilever beam are little influenced and its elastic stiffness is larger than that of joint without splice, though the beam flange and web are weakened.
结果表明：虽然带悬臂梁段拼接节点的梁翼缘、腹板均有所削弱，但其初始刚度和极限承载力受影响较小，且弹性刚度高于无拼接的焊接节点； - In pressure vessels, C and D seam which are located at the joint of flange, tube-shape object, jointed tube, and head of pressure vessels separately are the most complex seams.
压力容器设备中法兰与筒体、法兰与接管连接处的C类焊缝和封头端部、筒体上马鞍形的D类焊缝是最为不规则的且施焊工艺最为复杂的焊缝。 - The paper introduced structure character of the soft rapid joint in piping, and compared with the flange connection, proved that it has the character of high connection performance, good seal feature and economic performance, it has been proved with certain applicable value.
介绍了柔性快速管接头的结构特点，并与法兰连接形式相比较，结果证明，柔性快速管接头具有良好的连接性能，密封性能以及经济性能等，具有一定的应用价值。 - Research on the structural design of universal joint folk flange
万向节叉法兰盘的结构设计研究 - The broken analysis of universal joint shaft middle flange
轧机万向接轴中间法兰断裂分析 - The purpose of this essay is to analyse the performance of the joint when no stiffing plate were planted inside the box-column at the position which at the same hight of the tension side of the beam flange.
本文的目的，就是分析梁受拉翼缘处，当箱形柱内不设置加劲肋时节点的受力性能。 - Improving measures should include: change the nonstructural form of joint, remove the notch effect on groove weld in beam flange, modify the configuration of sphere corner, and strengthen the connection between web and column.
讨论总结了改进节点设计的途径和改进措施，如：改变节点的构造形式，去除梁翼缘焊缝衬板缺口效应，改进扇形切角构造，加强梁腹板与柱的连接等。 - Breaks Treatment of Joint Bolt between Quill Shaft Flange and Mill Shell
水泥磨中空轴法兰与筒体联接螺栓断裂的原因与处理 - The flange joint is a common connection form of high-rising steel tower structure, and bolt looseness of flange is the damage with facilitated occurrence in the structure.
法兰连接是输电线塔等高耸钢结构中常用的一种连接方式，法兰处螺栓的松动是结构容易发生的损伤。 - Welding deformations due to circumferential welds at the joint between the large cylindrical shell and the flange is studied by model test.
利用模型试验研究了大型圆柱形壳体与法兰对接环形焊缝的焊接变形。 - The changes of the radial deformation and the flange's planeness are induced by the circumferential weld at the joint between the cylindrical shell and the flange;
圆柱形壳体与法兰对接环形焊缝将引起壳体的径向变形及法兰平面度的变化； - Level 2, diagonal strut mechanism formed by inner joint core concrete within the flange width.
层次二：翼缘框宽度范围核心区内部混凝土的斜压杆机构； - The conclusion is that the condition of stress concentrating on the joint of hydraulic turbine blade flange and inner edge is improved notably.
结果表明，根部加厚后水轮机叶片法兰与内缘交接处应力集中现象得到显著改善。 - The material selection of reactor, strength calculation, structure design ( including welding joint and flange seal face) and matters needing attention in equipment manufacture were analyzed and discussed comprehensively by the author.
作者对反应器的选材、强度计算、结构设计（包括焊接接头和法兰密封面）及设备制造中应注意的问题进行了较全面的分析和论述。 - The influence of copper flange pad and shape of solder joint on the reliability were analyzed. The results showed the lower copper flange height leads to a more reliable TSV.
研究了TSV焊盘高度和焊球形状对其可靠性的影响，结果表明焊盘高度越小，可靠性越高。 - For the joint in the plane frame, the thickness of the column flange has big influences on the dint and distortion to the joint. The thicker the column flange is, the higher the extreme bearing capacity is, and the both nearly assume the linear relations.
对于平面框架中节点，柱翼板厚度对节点受力和变形影响很大，柱翼板越厚，节点极限承载力越高，并且二者几乎呈线性关系。